896 Royalty-Free Audio Tracks for "Filling Tool"

Sound of screws being moved around.

Sound of a screw being dropped on metal.

Turning on and off dremel and increasing and reducing engine speed. Recorded with zoom h1. Ligando e desligando micro retífica e aumentando e reduzindo a velocidade do motor. Gravado com zoom h1.

Polishing of a 7ct diamond in a diamond workshop in antwerp.

Tool for cut steel and iron. Record use h4n pro, 2019. 01. 09 ≈12:00.

Pressure cooker recorded with a stereo mic at 48 khz/ 24 bits.

This is the sound produced by a voltmeter when it detects that there is electrical continuity. This tool is used at ubica lab (upf). Their research areas are enclosed within the general disciplines of ubiquitous computing, contextual intelligence and cognitive systems, using sensors and radiofrequency identificaiton (rfid).

This is the sound of a tape measure from ubica lab (upf). Their research areas are enclosed within the general disciplines of ubiquitous computing, contextual intelligence and cognitive systems, using sensors and radiofrequency identificaiton (rfid).

Recording of electrode welding noise of a tube.

Impact wrench working in the open air :). Recorded witch lenovo p2 smartphone.

Electric wood sander sanding a sheet of ply wood. Hard, loud and abrasive sound, high volume low pitch. Recorded inside a workshop with a zoom h6 recorder. Audio was post-processed to boost the audio. Wood sander was a bosch 230v.

Miter saw sound. Whole on-cut-off way.

Selection of sounds.

Extending a telescopic tool, slower this time. A pair of sennheiser me64s into a tascam dr40.

A single click of a wratchet wrench. Check out the rest of the pack for some other versions.

Uryu uag50 pneumatic angle grinder started four times. Recorded in 24-bit 96khz with a tascam dr-40 and a sony ecm-nv1. For details on sow: blacksmith ed1 sound pack see: www. Oree. Storijapan. Net/praxis/sound-of-work.

Desoutter pneumatic drill going through metal, short. Recorded in 24-bit 96khz with a tascam dr-40 and a sony ecm-nv1. For details on sow: blacksmith ed1 sound pack see: www. Oree. Storijapan. Net/praxis/sound-of-work.

Unbranded impact wrench started four times against a bench. Recorded in 24-bit 96khz with a tascam dr-40 and a sony ecm-nv1. For details on sow: blacksmith ed1 sound pack see: www. Oree. Storijapan. Net/praxis/sound-of-work.

Holman nc4 pneumatic chipping hammer started four times. Recorded in 24-bit 96khz with a tascam dr-40 and a sony ecm-nv1. For details on sow: blacksmith ed1 sound pack see: www. Oree. Storijapan. Net/praxis/sound-of-work.

Atlas copco r4n pneumatic hammer started four times and it sounds mellow. Recorded in 24-bit 96khz with a tascam dr-40 and a sony ecm-nv1. For details on sow: blacksmith ed1 sound pack see: www. Oree. Storijapan. Net/praxis/sound-of-work.

Unbranded straight die grinder started four times. Recorded in 24-bit 96khz with a tascam dr-40 and a sony ecm-nv1. For details on sow: blacksmith ed1 sound pack see: www. Oree. Storijapan. Net/praxis/sound-of-work.

Recorded stereo xy mic configuration with two akg ck93 capsule mic with zoom h6.

Tools traffic subway platform start to leave china.

A few sounds of using a normal metal screw-clamp. The sound has been close mic-ed. Recording equipment: akg c214 / focusrite saffire pro 24.

Sounds of using a power saw and increasing the amplitude and speed of the blade.

Synthesized clinking and clanking effect.

A pneumatic air tool (jackhammer) was used to lower some concrete blocks on the exterior of our garage. I was inside the house recording it with a zoom h2 recorder. So this was recorded through an insulated wall. This is the shorter recording.

This is a trnsformation of the original sound: http://www. Freesound. Org/people/xserra/sounds/254374/ , with the parameters:. For synthesis:window type: hammingwindow size: 801fft size: 2048minimum f0: 160maximum f0: 260number of harmonics: 80threshold: -100minimum length of harmonics:. 1stochastic decimation factor : 0. 2minimum sine duration : 0. 1. For transformation :frequency scaling factors : [0, 0. 4, 1, 0. 4] <- (make frequency lower)frequency stretching factors : [0, 1, 1, 1] <- (no change)timbrepreservation : 1 <- (no change)time scaling factors : [0, 0, 1, 0. 7] <- (faster).

A 6-in-1 brass hammer being dismantled and put back together. I am aware that there are a few "pops" in the sound, but i am not completely sure how to remove them, so i left them there in case someone with more experience in audio editing wants them. The sounds i recorded from the smallest possible parts of the hammer are not included because they were way too quiet to be useful :1.

Three turns of a ratchet, mixed to sound a bit fuller. Recorded on cubase using an m-audio mic.

Someone welding part of a car. Senn 416 > sound devices 302 > tascam dr-40 48khz 24bit.

Bell-like sound created in pro tools by treating a hi-hat sample with the grm reson plug-in. I think of it as a blend of a gong, bell and triangle.

Vlc ratchet tightened four times. Recorded in 24-bit 96khz with a tascam dr-40 and a sony ecm-nv1. For details on sow: blacksmith ed1 sound pack see: www. Oree. Storijapan. Net/praxis/sound-of-work.

A piece of metal being dropped on the floor.

A somewhat large drill powering up and losing power.

Minimalist beat captured in a natural setting, probably some siding on a building being replaced. Mixes metal rattling (like screws or coins) with hammering and a low background voice. Portions have been looped and mixed, could be cut and looped in various patterns.

1 bar of a toolbox close mic'd and playing at 114bpm.

Sound of a measuring tape being extended.

Bolt cutter opening the lock of a metal cage. It sends the lock flying with a sound that goes 'ping'!.

Pretty fast engraving process sound (for the game, i guess?). Dethrok recorded the sound of engraving tool on metal, i just shortened it to 3s.

Moving the arm of an old coffee mill. Zoom h1.

Cutting a tile of wooden flooring with a handheld circular saw.

Cutting a tile of wooden flooring with a handheld circular saw. Recorded in cluj, romania.

The sound of going through an unorganized tool box. Recorded using a sony ic recorder and processed in fl studio's edison.

The sound of going through an unorganized tool box. Recorded using a sony ic recorder and processed in fl studio's edison.

Twisting a socket wrench quickly once. Recorded with a tascam dr-40.

Twisting a socket wrench multiple times at varying speeds. Recorded with a tascam dr-40.

Sound of a bosch screwdriver recorded with a bm-8000 mic, edited on audacity.

The sound of an electric screwdriver shortly running at different speeds.